Welcome to pbjtech.com
Embedded Control Technology
HOME PRODUCTS SALES CONTACT

THUMBNAIL 2106 VGA PROCESSOR MODULE

A simple plug-in module to add VGA to your pcb. Has on-board 3.3V and 1.8V regulators and accepts 3.3V to 10V in. Can also be used as a plug-in CPU module. Employs an LPC2106 with 64K RAM so you can display more lines of VGA data. Video specifications are similar to the noPC but this unit is able to display 192 pixels x 480 lines x 8 colors without additional circuitry. Like the noPC, this module can serve as a simple slave display or the application can run from the module itself.
Thumbnail VGA generator CPU          
PIN CONNECTIONS
1 R - CAP 2 GND
3 G - RXD1 4 HSYN
5 B - TXD1 6 VSYN
7 SSEL 8 RX+
9 MISO 10 RX-
11 MOSI + SDA 12 TX+
13 SCK + SCL 14 TX-
15 GND 16 VDD
     


LPC2138/48 CPU DIP MODULE

The LPC2138 or LPC2148 mounted on a 0.6" 40-pin DIP module.  This is preloaded with the same IVOS as is used on the noPC so you can be instantly communicating and programming with this module.

An optional USB type B connector may be mounted directly on the PCB for use with the LPC2148's USB port. There are also RS-232 and USB-UART bridge interface cables available separately.


LPC2148/38 DIP module		        
PIN CONNECTIONS
1 P0.0 40 P0.31
2 P0.1 39 P0.30
3 P0.2 38 P0.29
4 P0.3 37 P0.28
5 P0.4 36 P0.27
6 P0.5 35 P0.26
7 P0.6 34 P0.25
8 P0.7 33 P1.16
9 P0.8 32 P0.23
10 P0.9 31 P0.22
11 P0.10 30 P0.21
12 P0.11 29 P0.20
13 P0.12 28 P0.19
14 P0.13 27 P0.18
15 P0.14 26 P0.17
16 P0.15 25 P0.16
17 P1.20 24 X2
18 EINT0 23 X1
19 RST 22 VREF
20 GND 21 +3.3V

CE0067 COMS DATA LOGGER

noPC configured as an RS-232 data logger. It will take more months than I can wait to fill the SD card. This type of enclosure is also available for the standard noPC. noPC-0067 enclosure

CE0058 RS-232/RS-485 PROTOCOL CONVERTER

Communications processor in a DIN rail mount case. One coms port is RS-232 + handshake while the other is either RS-232 or RS-485.
RS-232/RS-485 Protocol Converter


CE0910 ADVANCED COMMUNICATIONS PROCESSOR

An expandable communications module that is interconnected over a 10-way IDC cable. Dual coms ports, one RS-232, the other RS-485/422 are opto-isolated from the processor. These mount up easily in a 1U rack with up to 20 modules, that's a lot of busy talking. Designed primarily for industrial communications. Complete rack mount units based on these modules are also available.
CE0910 Advanced Communications Processor

LCDTAB II   SERIAL CHARACTER LCD BACKPACK

Need to run character LCDs from a serial port? This one will run directly from RS-232, RS-485, or logic levels at a default baud rate of 19,200. Multiple units may be addressed from the one serial port. The unit's address and operating modes are programmed into Flash by the user and once it's been set it will hold that configuration. The CPU is a 16-bit MSP430 and the firmware can be upgraded by the user via the JTAG connector.

The LED-type backlight brightness and LCD contrast are controlled directly from software. An infra coms option is available which uses a standard 38Khz remote control sensor plus a buffered IR transmit LED accessible via the connector.

PIN CONNECTIONS
1 RS-485 A or TTL
2 RS-485 B or RS-232
3 GND
4 +12V
5 IR LED-
6 IR RXD-



OTHER PRODUCTS

USB-UART to RS-232 cable
RS-232 to logic level cable
MSP430 Based controllers
Dual 32 Segment LED Bargraph Display
MiniMux cascadable 4 port RS-232 Multiplexer